91 BRIGHT WHITE 24 VOLT LED WHITE INTERIOR LAMP WITH ON / OFF / DOOR SWITCH.

WITH IS COMPACT SIZE OF 143mm X 38mm, COMES COMPLETE WITH 400mm OF WIRE READY TO BE FITTED.

KC3E features of superior illumination performance, high-beam operating mode and focused beam make it very suitable for most underground mining applications.

KC3E has two LED light sources. The Main LED, a high-power LED located in the middle of the reflector, is for both normal and high-beam illumination. The Emergency LED, a low power LED located on the brim of the reflector, can operate for an extended period during an emergency.

KC3E is our only model charged through external electrodes rather than charging socket of the lamp

Operating Modes:

Four operating modes can be toggled using the button switch on top of the lamp.

NOTE:

• KC3E can only be charged using above charging facilities specially designed for KC3E. Therefore, KC3E is not compatible with other chargers and charging banks.
• KC3E is same as KC3D except charging methods.

Specifications

This AMBER 12 Volt 48 super bright LED's exceeds 700cd centre, they have this 700cd due to the fact that they have 30 degree LED's all in one unit LED printed circuit board and housing combination
Polycarbonate housing for strenght and durability complete with 150mm or wire in the centre of the light.

They have a huge range of use's- and the sky is the limit, and with the 3 Bolt holes on housing are the same dimensions as standard 4 inch arrow board shroud that you see on trafiic arrow boards and alike.

These are also Vibration resistant and with those 3 bolt holes for good ,mounting will not move in a wide range of applications.The back of lamp has provisions for 4 inch "O" ring for this purpose and to help to stop any movement between mating surfaces.
 

Great Low Voltage for mobile traffic lights - work site lights - weigh bridge's - underground lights - surface lights - or and where that the light would be great for, and being LED unlike the old types these will drawn hardly and current.

BRAND NEW 12 VOLT 61 WHITE LED WORK LIGHT, WITH ABS BLACK PLASTIC BODY. 

THE LIGHT HAS A BLACK ABS PLASTIC BODY FOR EXTRA STRENGTH - DURABILITY & STAINLESS STEEL BRACKET & BOLT THAT GIVES YOU A WIDE RANGE OF APPLICATIONS.

THESE LIGHTS ARE NOW BEING FITTED TO REAR'S OF 4WD'S AS BACK UP LIGHTS & COMP VEHICLES- THESE VERY BRIGHT & YOU WILL BE SUPRISED HOW GOOD THEY ARE.

THESE LIGHT WILL BUT SUIT ALOT OF DIFFERENT APPLICATIONS, WHERE A 12 VOLT LIGHT IS NEEDED. 4WD'S / CARAVAN'S / VAN'S / TRUCK'S / UTE'S / BOAT'S .

SPECS:

12 VOLT

0.38 AMPS DRAW @ 13.8 VOLTS

61 BRIGHT WHITE LEDS

BLACK ABS PLASTIC BODY

SLIM-LINE BODY

STAINLESS STEEL BRACKET & BOLT

CLEAR POLYCARBONATE LENSE FOR GREAT LIGHTING

126mm IN DIAMETER

400mm OF COLOURED WIRE

Please Contact us for qty's orders

sales@fcmining.com.au

This Red polyethylene Underground Fire Depot- comes complete with all the listed features below. They are a must for all mining & industrial applications where you need to have a good dry sealed environment for your fire fighting equipment.

 Size: 600mm x 790mm x 800mm

• Marine grade latches
• Consealed Space For Anti Tamer Seals To Be Fitted
• Stainless Steel Carry Handles For 2 x Person Operatiuon
• Moulded Hand Grips
• Telescopic Stainless Steel handles For Single Person Placement
• Lower Centre Of Gravity Increasing Stability
• Oversized Tyres To Assist In Maneurvering Over Rough Mining & Industrial Terrain
• Empty Weight - 22kg
• Dust Seal
• Visible Anti Tamper Seals
• Telescopic Stainless Steel handle
• Fixed hardward tray
• Lower centre of gravity for stability
• Oversized tires for rough terrian

Please contact us for large order costings on sales@fcmining.com.au

This White polyethylene fire hose reel cover, Would suit all 36 metre hose reel's. These are a must to protect your hose from damage from the sun or where there may be dirt or very dusty environment's.

They are very easy to fit and are able to be locked in place- for safety & security of your hose reel, From people who should not be touching them. Remembering these are life saving device's- Which could end up saving your life one day ?????

 They come with a grab handle on the top of the cover for easy removal when the hose is needed or for routine inspection's of fire fighting equipment.

The hose reel is also clearly marked FIRE HOSE REEL on the large face area.

Have a look @ the RED style that is also available. FCFHRC36R 

For the lock that will fit all series of hose reel cover's look @ FCFHRC

Please contact us for large order costings on sales@fcmining.com.au

12 VOLT 72 LED RED / AMBER STOP / TAIL / INDICATOR WITH 36 AMBER LED'S & 36 RED LEDS.

THES LAMPS HAVE A BLACK BASE WITH IN_BUILT REFLECTORS. THEY ARE WATERPROOF, SHOCK PROOF, VIBRATION PROOF, RUST PROOF & ARE MADE FROM POLYCARBONATE & ARE RESIN POTTED ASSEMBLY.

THIS MAKING THEM 100% FULLY WATER TIGHT & SUBMERASBLE.

H 100mm x W 304mm x D 32mm FITTED WITH 400mm OF WIRE-- THESE LAMPS HAVE A registered certified design No: 319855 

WE ARE INTERESTED IN TRADE ENQUIRIES & TRADE QTY'S EMAIL US FOR GREAT RATES

sales@fcmining.com.au

MULTI- VOLT 24 LED RED / AMBER STOP / TAIL / INDICATOR WITH 12 AMBER LED'S & 12 RED LEDS.

THES LAMPS HAVE A BLACK BASE WITH IN_BUILT REFLECTORS. THEY ARE WATERPROOF, SHOCK PROOF, VIBRATION PROOF, RUST PROOF & ARE MADE FROM POLYCARBONATE & ARE RESIN POTTED ASSEMBLY.

THIS MAKING THEM 100% FULLY WATER TIGHT & SUBMERASBLE.

H 100mm x W 304mm x D 32mm FITTED WITH 400mm OF WIRE-- THESE LAMPS HAVE A registered certified design No: 319069

WE ARE INTERESTED IN TRADE ENQUIRIES & TRADE QTY'S EMAIL US FOR GREAT RATES

sales@fcmining.com.au

MULTI- VOLT 24 LED RED / AMBER STOP / TAIL / INDICATOR WITH 12 AMBER LED'S & 12 RED LEDS.

THES LAMPS HAVE A BLACK BASE WITH IN_BUILT REFLECTORS. THEY ARE WATERPROOF, SHOCK PROOF, VIBRATION PROOF, RUST PROOF & ARE MADE FROM POLYCARBONATE & ARE RESIN POTTED ASSEMBLY.

THIS MAKING THEM 100% FULLY WATER TIGHT & SUBMERASBLE.

H 100mm x W 304mm x D 32mm FITTED WITH 400mm OF WIRE-- THESE LAMPS HAVE A registered certified design No: 319069

WE ARE INTERESTED IN TRADE ENQUIRIES & TRADE QTY'S EMAIL US FOR GREAT RATES

sales@fcmining.com.au

THIS 45 LED MULTIVOLTAGE RETRO FIT STOP / TAIL CARD FOR ALL JUMBO STYLE LIGHTS.

THE CARD ITSELF IS VERY EASY TO INSTALL, BASICALLY REMOVE YOUR OLD BULB'S & MOUNT THE CARD IN PLACE & HOOK UP THE WIRING TO THE MALE SPADE TERMINALS.

YOU WILL NEVER HAVE TO REPLACE BULBS EVER AGAIN & THIS MAKES LIFE EASIER FOR THOSE DRIVERS OUT THERE WHO DO ALOT OF MILES & CANT AFFORD TO BE PULLED UP WITH A LIGHTING PROBLEMS.

DONT PAY BIG MONEY FOR COMPLETE JUMBO STYLE LIGHTS- IF YOU ALREADY HAVE BULB TYPE JUMBO'S, THEN HERE IS YOUR ANSWER SO YOU TO CAN HAVE LED LIGHTS.

YOU CAN SMARTEN UP ANY VEHICLE USING THESE CARDS & THERE IS A WIDE RANGE OF USES- NOT JUST FOR VEHICLE TAIL LIGHTS.

SPEC'S

MULTIVOLTAGE

45 BRIGHT LED'S 

175MM LONG  X 105MM WIDE 10MM DEEP

MALE SAPDE TERMINAL FOR EASY INSTALL

• No electric cord can be bumped or tangled;
• Significantly reduces miner’s burden;
• No back pain and injury any more;
• No acid or toxin to spill;
• No heat on lens surface; No burning parts to cause fire;
• IP67 case for the harshest mining environment;
• As a warning lamp to wear on your back or attach to an object.

• No cord and heavy battery that hinders work performance;
• Minimized size and weight reduces burden on miners;
• Adjustable angle and portability for extraordinary flexibility;
• Time saved in issuing light to miners, attaching light and moving to workplace;
• Less staff in Lamp Room;
• Various applications for one lamp to meet different illumination requirements.

• No electric cord can be bumped or tangled;
• Significantly reduces miner’s burden;
• No back pain and injury any more;
• No acid or toxin to spill;
• No heat on lens surface; No burning parts to cause fire;
• IP67 case for the harshest mining environment;
• As a warning lamp to wear on your back or attach to an object.

• No cord and heavy battery that hinders work performance;
• Minimized size and weight reduces burden on miners;
• Adjustable angle and portability for extraordinary flexibility;
• Time saved in issuing light to miners, attaching light and moving to workplace;
• Less staff in Lamp Room;
• Various applications for one lamp to meet different illumination requirements.

12v 20 WHITE PIRAHNA LED BOARD WITH an adhesive backing and T10 wedge base fitted with 100mm wire between connector and light board.

The board is 50mm X 50mm ideal for inside caravans (JAYCO) to replace the standard T15 16w bulb, gives a light comparison too a 20w incandescent globe but draws only 0.2amp @ 13.8v

These LED boards are great for people who do alot of off road travelling either in a Caravan / Camper Trailer / Trucks / Utes, where you need to use the least amount of power where you can.

With these LED boards you will stop drawing all of those large amps that you will be with the current type of bulb / globes in use.

(complete lamp assembly shown is not included-display purpose only )

Caravans are common to have high wattage incandescent globes that all amount to a high current draw, if wanting to lower power consumption then leds are the way to go, here you will find straight LED globe replacements and our new universal LED boards that will give you a better light output than your standard globes and draw on average 1/10 of the power

FOR LARGE ORDERS PLEASE CONTACT USE ON sales@fcmining.com.au

KC3R is designed for underground operations. It integrates a red LED beacon into a cordless caplamp to achieve both normal white illumination in front and flashing red warning on the back when worn on the side of the helmet. The illumination LED operates at either Main level for normal use or Auxiliary level for conservation of power. The warning beacon utilises 7 red LEDs behind a red scattering cover to enable wide angle viewing. You can use illumination only, beacon only or both for the whole 12-hour work shift. The features of high light intensity and back warning light make it very suitable for in underground mines and other applications where both illumination and warning are required. Operating modes: 1. Auxiliary illumination: for low illumination or longer duration 2. Main illumination: for general illumination. 3. Warning: Red flashing lamp on the back for warning. 4. Main illumination + Warning: Combination of Main illumination and Warning states. Four operating states can be toggled by pressing the button switch. From the OFF condition, pressing the button turns the lamp ON to whatever condition it was in when turned OFF. Pressing the button again will now toggle to the next mode of operation. At any time, pressing the button and holding it for two seconds will turn the lamp OFF.
Side-mounting Fit the lamp to a side lamp bracket There are two ways to mount the lamp on a helmet and there are two side caplamp brackets in every package. The lamp is fitted in either side lamp bracket in the same way. Simply align the slot of the caplamp clip to the bracket bar and slide the lamp in.
Fit the side lamp bracket to a helmet Insert model of bracket, SLBI, can be inserted in the slot of a helmet. It is suitable for a miner's helmet. Screw model of bracket, SLBS, can be screwed onto the brim of the helmet. It is suitable for any other helmets.
Adjustable angle The bracket is adjustable in the left-right direction to set a distance from the helmet so other attachments such as a visor will not block the light. The lamp is also angle adjustable in the forward-back direction to set the light projecting direction. Using the both bracket and lamp adjustments, an all-around angle is achieved.
Left-right adjustable		Forward-backword adjustable
Specifications Model Specifications Battery capacity 2.8 AH Luminous intensity 1500lx for  Main mode Duration 14 hours for Main+Warning mode Charging time 7 hour Weight 135g General Specifications Battery voltage 3.7V Li-ion Battery lifetime 80%C after 500 full charging cycles LED lifetime 30,000 hours Enclosure rating IP67 Warranty 1 year replacement warranty

WE ARE INTERESTED IN TRADE ENQUIRIES & TRADE QTY'S EMAIL US FOR GREAT RATES

sales@fcmining.com.au

WORLDS 1st FULLY IECEx & ANZEx CERTIFIED 

UNDERGROUND COAL MINING CORDLESS LED CAP LAMP

The KC3D-Ex has two LED light sources. The Main LED, a high-power LED located in the middle of the reflector, is for both normal and high-beam illumination. The Emergency LED, a low power LED located on the brim of the reflector, can operate for an extended period during an emergency.
KC3D-Ex features a superior illumination in just 140g, even less than the headpiece of a traditional caplamp. It is suitable for most underground mining applications.

This lamp is the standard series of lamps, using a single desktop type charger. for the mine site applications where the KC3E-EX is used please follow this link to board type charged lamps.

http://www.fcmining.com/index.php?page=details&prod=1816&cat=150&group=29

Operations:

There are three operating modes.

Main mode: (level 2): For normal working operation, delivering good illumination in excess of 14 hours duration.
High-beam mode: (level 3): Strong light beam for long distance projection, spotting, etc. Should only be used for short periods because the heavier battery drain shortens light duration in this Mode to around 8 hours.
Auxiliary mode: (level 1): Power saving for long operation and low level illumination.
Off: The Caplamp is switched off.

Features of the lamp:

– The lamp Always starts up from the Main Mode when switched on.
– By toggling the operating button the Caplamp goes through Main Mode > High-Beam Mode > Auxiliary Mode > Off Mode
– Holding  the button down for 2 seconds switches the Caplamp off directly.
– If the lamp is kept in the High-beam Mode for 20 minutes, it will automatically goes to the Main Mode.

Cordless LED cap lamp Benefits:

OHS & SAFETY

• No electric cord can be bumped or tangled
• Significantly reduces miner’s burden
• No back pain and injury any more
• No acid or toxin to spill
• No heat on lens surface; No burnable parts to cause fire
• IP67 case for the harshest mining environment
• As a warning lamp to wear on your back or attach to an object
• No personal injury from battery packs 

WORK EFFICIENCY & TIME SAVING

• No cord and heavy battery that hinders work performance
• Minimized size and weight reduces burden on miners
• Adjustable angle and portability for extraordinary flexibility
• Time saved in issuing light to miners, attaching light and moving to workplace
• Less staff in Lamp Room, No need for topping up of acid in battery
• Various applications for one lamp to meet different illumination requirements.

DAMAGE TO EQUIPMENT & PERSONAL

• No more doors on shuttle cars latches
• Less damage to machinery seats from the battery pack
• No more damage to emico's & drift runners doors
• No more damage to miner LCD displays & levers & joysticks

KC3E-Ex is world’s only Cordless Miner’s Caplamp charged through external electrodes rather than charging socket of the lamp.

The KC3E-Ex has two LED light sources. The Main LED, a high-power LED located in the middle of the reflector, is for both normal and high-beam illumination. The Emergency LED, a low power LED located on the brim of the reflector, can operate for an extended period during an emergency.
KC3E-Ex features a superior illumination in just 140g, even less than the headpiece of a traditional caplamp. It is suitable for most underground mining applications.

Operations

There are three operating modes.

Main mode (level 2): For normal working operation, delivering good illumination in excess of 14 hours duration.
High-beam mode (level 3): Strong light beam for long distance projection, spotting, etc. Should only be used for short periods because the heavier battery drain shortens light duration in this Mode to around 8 hours.
Auxiliary mode (level 1): Power saving for long operation and low level illumination.
Off: The Caplamp is switched off.

Features of the lamp

– The lamp Always starts up from the Main Mode when switched on.
– By toggling the operating button the Caplamp goes through Main Mode > High-Beam Mode > Auxiliary Mode > Off Mode
– Holding  the button down for 2 seconds switches the Caplamp off directly.
– If the lamp is kept in the High-beam Mode for 20 minutes, it will automatically goes to the Main Mode.

Cordless LED cap lamp Benefits

OHS & SAFETY

• No electric cord can be bumped or tangled
• Significantly reduces miner’s burden
• No back pain and injury any more
• No acid or toxin to spill
• No heat on lens surface; No burnable parts to cause fire
• IP67 case for the harshest mining environment
• As a warning lamp to wear on your back or attach to an object
• No personal injury from battery packs 

WORK EFFICIENCY & TIME SAVING

• No cord and heavy battery that hinders work performance
• Minimized size and weight reduces burden on miners
• Adjustable angle and portability for extraordinary flexibility
• Time saved in issuing light to miners, attaching light and moving to workplace
• Less staff in Lamp Room, No need for topping up of acid in battery
• Various applications for one lamp to meet different illumination requirements.

DAMAGE TO EQUIPMENT & PERSONAL

• No more doors on shuttle cars latches
• Less damage to machinery seats from the battery pack
• No more damage to emico's & drift runners doors
• No more damage to miner LCD displays & levers & joysticks

91 LED MULTIVOLTAGE 4" ROUND POLYCARBONATE REVERSE LIGHT ASSEMBLY- WITH MOUNTING FLANGE WITH A RUBBER GROMMET MOUNTING.

THIS ROUND LIGHT IS GREAT FOR ALL THOSE APPLICATIONS WHERE FLUSH MOUNTING IS A MUST, THESE ARE VERY EASY TO INSTALL, CUT YOUR HOLE & DRILL THE HOLES & INSERT RUBBER GROMMET & POP THE LIGHT IN.

THIS LIGHT IS GREAT FOR TRUCKS, TRAILER, CARAVANS, UTES, 4WDS, MACHINERY, OR ANY WHERE THAT A NORMAL REVERSE LIGHT MAYE GET BUMPED, THESE WILL JUST PUSH THE ASSEMBLY OUT & NOT BREAK IT LIKE FIXED LIGHTS.

HAVING A RUBBER GROMMET BODY ALLOWS THIS LIGHT TO BE USED ON SOME OF THE MOST HARSH CONDITIONS WITH OUT FAILING, BEING FULLY WATERPROOF, SHATTERPROOF, VIBRATIONS PROOF, FULLY RESIN MOULDED BACKING.

THE LAMP COMES WITH 400mm OF COLOURED WIRING FOR EASY WIRING UP, THESE WILL FIT IN TO YOUR OLD BULB TYPE OF 4" ROUND LAMPS THAT YOU HAVE NOW.

SPEC'S

MULTIVOLTAGE

91 LEDS

POLYCARBONATE

400mm OF COLOURED WIRE FOR EASY WIRING

139mm IN DIAMETER  X 44mm DEEP

RUBBER MOUNTING

ALSO AVAILABLE IN SOLID MOUNTING, CLICK ON LINK BELOW.

http://www.fcmining.com.au/index.php?page=details&prod=1809&cat=256&group=28

FOR LARGE QTYS PLEASE EMAIL US ON sales@fcmining.com.au

12v motion day/night sensor, 2 styles of wall mount brackets supplied, can apply a max load of 6amp, Has 1 pos in, 1 pos out, 1 common earth, ideal in caravans, RVs, Home and gardens.